Using two colours, weavers get a bracelet that is compact and has a pattern that is beautifully framed by its paired colour.This bracelet design uses knots of alternate coloured paracord melted together to create an effect similar to prayer beads. how funny. Finish the bracelet in a variety of ways including a knot, a bead, or a cobra weave shown in the picture above.Want to use up some scraps of paracord? The main side features waves, but the reverse side looks similar to a heart pattern.Inspired by Michonne’s trademark katana on The Walking Dead and katana swords in general, the Katana Wrap design uses a basic Fishtail design then wraps it in a modified traditional tsuka-maki katana handle wrap. The paracord bracelet is the combination of the Curling Millipede tying technique and alternating Square Knots. A 10 inch bracelet uses about five feet of cord. You'll need two 3 inch nails with a head and some superglue. It doesn't take long to master this pattern. However, one of the best features is that it is reversible.
Pattern came from blog.swiss-paracord.chThis paracord cross project uses 20 ft of paracord cut into four 5 ft sections. Use a large cord stop or a two-hole cord stop to make it adjustable.Make a colorful bracelet with this multi-strand bracelet with easy open magnet clasp. Use a 3/8 or 1/2 inch buckle to finish.This siren bracelet is made with urban camo paracord and neon orange 275 paracord to highlight the edges.If you like the wide bracelets, this Manta Ray is a good one. This bracelet is adjustable with ten rosary paracord "beads" and a paracord cross on one end.Create a round braid with micro cord. Moreover, you can turn a paracord bracelet into a multi-tool by using fasteners that have a whistle and/or ferro rod (a flint spark lighter).This Dr. Who-themed bracelet uses blue and white to create a unique interlocking design that manages to cram the usual amount of cordage into a compact design.The Cyclone Wrap presents an awesome two-toned original design that features an eye-catching division of colour right down the middle and looks as though it is wrapped around another design. We used 425 paracord, but any size cord will work as well. You'll need just over six feet total.This wide bracelet pattern has a V shape along with a stitched look down each side. This bracelet is about 1 3/8 inches wide.This bracelet can be a little tricky to tighten at first but once you get the hang of it you get a nice design. You'll need a lacing needle to add the coyote color cord at the end.The Snow Cap 550 paracord in the center makes the V shape design in our Rocky Path bracelet. This is a wide 1 3/8" bracelet that uses about 20 ft total in cord.Here's a new tutorial using the Para-claw knife buckle instead of a traditional side release buckle. http://www.boredparacord.com http://www.paracord.com Use Promo Code: OHYEAH and save 10% on your first order Want to make things even harder?
The disk in the middle can be replaced with the two hole dog tags or shoelace charms.Use any size cord from Type 1 to 550 paracord for this simple bracelet. Check us out! Using one of our lacing needles or fid is very useful.Here is a slight variation on the regular fishtail design bracelet. You can make this with 2 or more colors. This also ends up being slightly wider than a fishtail bracelet at 3/4 inch wide.This tutorial for a monkey fist uses about three feet of paracord and a steel ball. The wire makes the bracelet stiff and bendable to that it is easy to slip on and off the wrist.Thick, wide, and labour-intensive – creating this design takes a lot of work, but is so worth it. However, while you can also clip things onto the loops of this bracelet, the loops are more compact and less likely to snag.Stepping up the difficult just a bit, if only because of the addition of a dowel rod, the Herringbone is one design that looks more complex than it actually is.