It print sometimes just few drops then continue normally, and then some other drops, etc.
I get good layer adhesion with Sainsmart TPU printed between 210 and 220C, but I have to print extremely slowly due to my Bowden setup. You need to change the extruder steps on the Mega-S (it's a different stepper motor).As you can see on the other images of the white boat, the wall are not perfectly straight and the overall quality isn't perfect, any advice ? I went back to the stock 1.1.2 firmware with the annoying startup beep.. and use the stock settings in cura. It's just that sensitive.I'll try to level it again, what do you guys use for layer height ? I went back to the stock 1.1.2 firmware with the annoying startup beep.. and use the stock settings in cura. I would always get shitty print closer to 0.3. I went back to the stock 1.1.2 firmware with the annoying startup beep.. and use the stock settings in cura. Mine look flattened, and they're fused to each other.What are you using to level? The MEGA 03 version_V1.1.2 or the Mega-s upgraded firmware_V1.2.0 ? TPU produces durable, rugged prints that are still flexible and bendable. Most of the time, it just print tiny drops instead of a continuous line. Looking to experiment with some new flexible filaments? In the normal "Print settings" Cura panel, change the following settings:Now that the machine itself is configured, you can optionally change a few print profile settings for the Mega X. firmware will help a lot to keep it even across your whole surface.Paper must not easily go , you must feel some frictionDo you have a Mega-S or an i3 Mega? Finally, change the printer name from "Anycubic i3 Mega" to "Anycubic Mega X" and click Add. Use Direct Drive Extruders. I'd recommend upgrading the firmware too, that will ensure perfect first layersdid you try to print with 0.2 or less layer height?
The MEGA 03 version_V1.1.2 or the Mega-s upgraded firmware_V1.2.0 ? the only thing I really change is print speed, I set that to 40-50 and turn on support or tree support.. and temp settings are 200/60 and usually use. your lines don't look squashed at all tho and they arent touching so i'd think it's the gap/leveling. Extruding at temperatures between ~190-230C, PLA does not require a heated print bed to successfully adhere to the build plate. .2/.3 layer heights, depending on the quality I want.. that's about it.. TPU Material. Somit lässt sich TPU Filament verarbeiten, ohne dass der Bowden Extruder umgebaut werden muss. Mine look flattened, and they're fused to each other.What are you using to level? Temperature try 205 deg...Make sure your nozzle isnt clogged? When you buy a tool or material through one of our Amazon links, we earn a small commission as an Amazon Associate.Follow @howchoo and learn cool things:If you see "Anycubic Mega X" as a selectable option, it means Cura has been updated to include the Mega X natively. if yours is like that then i'd wonder about under extrusion? Looking for optimal Anycubic i3 Mega Cura settings? However, I'd say both of those are not really good. For the firmware, which one ? For best results, print with this filament at slower speeds below 30mm/s. TPU produces durable, rugged prints that are still flexible and bendable. Please not that it is a scaled down model, the black boat is only here to show you the original scale in comparaison.Step 1 is the most important step by a 3d PrinterLooks to me like you have too much space between the bed and the head. Higher print speeds can cause the filament to compress and will most likely result in a jam. If you change filament and get lines that separate you probably have a filament not thick enough so you need to set this in cura.
In addition to printing in PLA and ABS, the Mega S also masterfully prints in TPU and PETG filaments. You need to change the extruder steps on the Mega-S (it's a different stepper motor).As you can see on the other images of the white boat, the wall are not perfectly straight and the overall quality isn't perfect, any advice ? I tried witht he 1.1.2 and it says udapte successfull but it still shows 1.1.1 on my printerReduce the print speed to 40mm/s. the only thing I really change is print speed, I set that to 40-50 and turn on support or tree support.. and temp settings are 200/60 and usually use. I'd really recommend the new firmware upgrade, tons of improvementsare you sure your bed is level? For best results, print with this filament at slower speeds below 30mm/s. Printing at temperatures between 220-240C, PETG works great with or without a heated print bed.The best thing about PLA is how versatile it is. Your lines aren't touching each other, or squashed down at all.